,

Stainless Steel Shoulder Dowel Pin – Stepped, Through-Bore

Qimao Metal Manufacturer Stainless Steel Shoulder Dowel Pin – Stepped, Through-Bore has a stepped body and a full through-bore. The ground shoulder seats flat against the plate, so press depth stays repeatable. Made for fixtures, molds and quick-change tooling where a solid dowel won’t pass a bolt or ejector rod.

Categories: ,

QM Metal manufacturer and production, welcome inquiry!!

https://youtube.com/shorts/8GGVeO5XHoM?si=Z8uaOsKhUkSCjbOF

   

Product Brief :

The Stainless Steel Shoulder Dowel Pin – Stepped, Through-Bore from Qimao Metal Manufacturer does the locating, the shank does the holding. We square the shoulder face to the shank so the pin bottoms out flat instead of rocking on one edge—even a slight tilt here shows up as a wobble in the fixture after a few thousand cycles. The through-bore runs the full length in the same turning setup, which keeps it concentric with the shank; important if a bolt or ejector rod has to slide through without binding. Shank ground to h7 for a press fit or g6 for a slip fit, your call. Stainless 303, 304 or 316, hardened option available if the pin sees shear. Send the drawing with the step height, bore callout and fit class, and we’ll quote both features together.

Key Specs & Dimensions:
Product Name: Item No.: Material:               Measurement(mm): Surface Finish: Weight(g):
L: W: D:
Stainless Steel Shoulder Dowel Pin – Stepped, Through-Bore QM9062 Stainless steel

 

43.81 16.07/13.77/12.07/10.91 Polish 24.15

Product Details

Stainless Steel Shoulder Dowel Pin – Stepped, Through-Bore material is stainless 303, 304 or 316, with hardened alloy available when the pin sees shear load. Shoulder OD and height are machined to your drawing and squared to the shank, so the pin seats flat. Shank tolerance runs h7 for press fit or g6 for slip fit. The through-bore is turned in the same setup as the OD, held concentric so bolts or ejector rods slide through without binding. Head styles include round, diamond, flat and chamfered. Surface is passivated or plain machined. Inspection uses pin gauges, micrometers and CMM reports on request. Packing is oiled bag, carton and wooden case for export. Each lot is checked against the drawing before shipment, and setup sheets stay on file so repeat orders match.

Key Features:

1-Stepped shoulder: The Stainless Steel Shoulder Dowel Pin – Stepped, Through-Bore face is squared to the shank, so the pin bottoms out flat against the plate instead of rocking on one edge. That keeps press depth repeatable across thousands of cycles, not just the first assembly.

2-Full through-bore: Bored in the same turning setup as the OD, so it stays concentric with the shank. Bolts, ejector rods or air lines slide through without binding—something a solid dowel simply can’t do.

3-Ground shank: h7 for press fit, g6 for slip fit. Ground finish reduces galling on stainless, so the pin comes out clean if you ever need to pull it.

4-Stainless body: 303, 304 or 316 handles coolant, wash-down and humid plant air. Hardening optional when the pin takes shear at pivot points.

5-Diamond head option: Relieved head absorbs hole-spacing variation on the mating part, useful in checking fixtures where hole positions drift.

Use Cases:

  1. Fixture plate locating: The Stainless Steel Shoulder Dowel Pin – Stepped, Through-Bore bottoms metal-to-metal on the plate, so pin height stays consistent across the batch. Operators feel the seat, which cuts setup time on manual fixtures.
  2. Mold plate alignment: The stepped head guides the plate back into position without over-travel. The shoulder stops it at the right depth, protecting the alignment bore from repeated impact.
  3. Hollow-pin routing: The through-bore carries ejector rods, air lines or sensor leads where a solid pin won’t fit. Common in automation stations with crowded tooling plates.
  4. Quick-change tooling: Shoulder gives a hard stop, so swap-over stays repeatable shift after shift. No re-checking pin height after every change.
  5. Checking fixtures: Diamond head compensates for hole spacing on the mating part, so the gauge seats even when hole positions drift within tolerance.
  6. Pivot and hinge points: Hardened shoulder takes shear load where a plain dowel would wallow out the bore over time.

 

Reviews

There are no reviews yet.

Be the first to review “Stainless Steel Shoulder Dowel Pin – Stepped, Through-Bore”

Your email address will not be published. Required fields are marked *